请输入搜索词进行查询
搜索 <book_title>...
Veritas Access 安装指南
Last Published:
2018-05-28
Product(s):
Access (7.4)
Platform: Linux
- Veritas Access 简介
- Veritas Access 授权许可
- 系统要求
- 准备安装 Veritas Access
- 在 VMware ESXi 中部署用于安装 Veritas Access 的虚拟机
- 安装和配置群集
- 使用响应文件自动运行 Veritas Access 安装和配置
- 显示和添加群集节点
- 升级 Veritas Access和操作系统
- 使用滚动升级来升级 Veritas Access
- 卸载 Veritas Access
- 附录 A. 安装参考
- 附录 B. 配置安全 Shell 进行通信
- 附录 C. 手动部署 Veritas Access
显示群集中的节点
可以显示过去 15 分钟内群集中的所有节点及其状态、CPU 负载和网络负载。
如果使用 Cluster> show currentload 选项,则可显示从现在到下一 5 秒之内收集的 CPU 和网络负载。
显示群集中的节点列表
- 要显示属于群集的节点列表以及可添加到群集的系统,请输入以下命令:
Cluster> show
命令输出包括以下信息。请参见下面的示例。
节点
如果节点已添加到群集,则显示节点名称。如果节点仍在添加到群集的过程中,则显示节点的 IP 地址。
示例:
node_01
或
192.168.30.10
状态
显示节点的状态或系统的安装状态及系统 IP 地址(如果已安装系统)。
CPU
指示 CPU 负载。
pubethX
指示公用接口 X 的网络负载。
bondX
指示绑定 NIC X 的网络负载。
- 对于群集中已存在的节点,将显示以下内容:
Node State CPU(15 min) pubeth0(15 min) pubeth1(15 min) % rx(MB/s) tx(MB/s) rx(MB/s) tx(MB/s) ------ ------- ----------- -------- -------- -------- -------- snas_01 RUNNING 1.35 0.00 0.00 0.00 0.00 snas_02 RUNNING 1.96 0.00 0.00 0.00 0.00
- 对于正在群集中添加/删除的节点以及正在升级的节点,将显示以下进度:
Nodes in Transition Node/IP Operation State Description ------ --------- ----- ----------- 192.168.30.11 Add node FAILED Installing packages snas_03 Delete node ONGOING Removing node snas_01,snas_02 Rolling upgrade ONGOING Rolling upgrade phase 2
注意:
add node 和 delete node 操作不能同时执行。
- 要显示从现在到下 5 秒之内收集的 CPU 和网络负载,请输入以下命令:
Cluster> show currentload
输出示例:
Node State CPU(5 sec) pubeth0(5 sec) pubeth1(5 sec) % rx(MB/s) tx(MB/s) rx(MB/s) tx(MB/s) ---- ----- ---------- -------- -------- -------- -------- snas_01 RUNNING 0.26 0.01 0.00 0.01 0.00 snas_02 RUNNING 0.87 0.01 0.00 0.01 0.00 snas_03 RUNNING 10.78 27.83 12.54 0.01 0.00
对于群集节点上的每个可用公用接口,将显示网络接口的统计信息。