Veritas NetBackup™ Cloud Administrator's Guide

To configure a cloud storage disk pool by using the wizard

1. If the Disk Pool Configuration Wizard was launched from the Storage Server Configuration Wizard, go to step 5.

   Otherwise, in the NetBackup Administration Console, select either NetBackup Management or Media and Device Management.

2. From the list of wizards in the right pane, click Configure Disk Pool.
3. On the Welcome panel, the types of disk pools that you can configure depend on the types of storage servers that exist in your environment.

   The following is an example of the wizard panel:

   

   Read the information on the welcome panel of the wizard. Then, select the appropriate storage server type and click Next.

   The Storage Server Selection panel appears.

4. On the Storage Server Selection panel, the storage servers that you configured for the selected storage server type appear.

   The following is an example of the wizard panel:

   

   Select the storage server for this disk pool.

   After you select the cloud storage server, click Next. The Volume Selection wizard panel appears.

5. The Volume Selection panel displays the volumes that have been created already under your account within the vendor's cloud storage.

   Note:

   The following properties do not apply to cloud storage disk pools: Total available space, Total raw size, Low water mark, and High water mark.

   All these values are derived from the storage capacity, which cannot be fetched from the cloud provider.

   The following is an example of the wizard panel:

   

   To add a volume, click Add New Volume. A dialog box appears that contains the information that is required for a volume for your cloud vendor. In that dialog box, enter the required information. Use the following link to find the information about the requirements for the volume names.

   See About the cloud storage vendors for NetBackup.

   To select a volume, click the check box for the volume. You can select one volume only.

   After you select the volume for the disk pool, click Next. The behavior of the wizard depends on whether you configured encryption for the storage server, as follows:

   No encryption

   If you selected a volume on a storage destination that does not require encryption, the Additional Disk Pool Information panel appears. Go to the next step, step 6.

   Encryption

   If you selected a volume on a storage destination that requires encryption, a Settings dialog box appears in which you must enter an encryption pass phrase. The pass phrase is for the key group key for this storage volume and storage server combination. After you enter a pass phrase and then click OK in the Settings dialog box, the dialog box closes. Click Next in the Volume Selection wizard panel to continue to the Additional Disk Pool Information wizard panel. Continue to the next step, step 6.

6. On the Additional Disk Pool Information panel, enter or select the properties for this disk pool.

   The following is an example of the wizard panel:

   

   See Cloud storage disk pool properties.

   After you enter the additional disk pool information, click Next. The Summary panel appears.

7. On the Summary panel, verify the selections.

   If the summary shows your selections accurately, click Next.

   Veritas recommends that you save the KMS key group name and the KMS key name. They are required to recover the keys.

   See Saving a record of the KMS key names for NetBackup cloud storage encryption.

8. After NetBackup creates the disk pool, a wizard panel describes the successful action.

   The following is an example of the wizard panel:

   

   After NetBackup creates the disk pool, you can do the following:

   Configure a storage unit	Ensure that Create a storage unit using the disk pool that you have just created is selected and then click Next. The Storage Unit Creation wizard panel appears. Continue to the next step.
   Exit	Click Close. You can configure one or more storage units later. See Configuring a storage unit for cloud storage.

9. On Storage Unit Creation wizard panel, enter the appropriate information for the storage unit.

   The following is an example of the wizard panel:

   

   See Cloud storage unit properties.

   After you enter or select the information for the storage unit, click Next to create the storage unit.

   You can use storage unit properties to control your backup traffic.

   See Configure a favorable client-to-server ratio.

   See Control backup traffic to the media servers.

10. After NetBackup configures the storage unit, the Finished panel appears. Click Finish to exit from the wizard.