Veritas NetBackup™ Appliance 命令参考指南
- 概述
- 附录 A. Main > Appliance 命令
- 附录 B. Main > Manage > FibreChannel 命令
- 附录 C. Main > Manage > HighAvailability 命令
- 附录 D. Main > Manage > Libraries 命令
- 附录 E. Main > Manage > Libraries > Advanced > ACS 命令
- Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
- Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
- Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
- Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
- Manage > Libraries > Advanced > ACS > TestACS
- Manage > Libraries > Advanced > ACS > ViewVMconf
- 附录 F. Main > Manage > License 命令
- 附录 G. Main > Manage > MountPoints 命令
- 附录 H. Main > Manage > NetBackup CLI 命令
- 附录 I. Main > Manage > OpenStorage 命令
- 附录 J. Main > Manage > Software 命令
- Manage > Software > Cancel
- Manage > Software > Delete
- Manage > Software > Download
- Manage > Software > DownloadProgress
- Manage > Software > Firmware
- Manage > Software > Install
- Manage > Software > List
- Manage > Software > LiveUpdateClients
- Manage > Software > Readme
- Manage > Software > Rollback
- Manage > Software > Share
- Manage > Software > UpgradeStatus
- 附录 K. Main > Manage > Storage 命令
- 附录 L. Main > Manage > Tapes 命令
- 附录 M. Main > Manage > Certificates 命令
- 附录 N. Main > Monitor 命令
- 附录 O. Main > Network 命令
- Network > Configure
- Network > Date
- Network > DNS
- Network > Gateway
- Network > Hostname
- Network > Hosts
- Network > IPv4
- Network > IPv6
- Network > LinkAggregation
- Network > NetStat
- Network > NTPServer
- Network > Ping
- Network > SetProperty
- Network > Show
- Network > TimeZone
- Network > TraceRoute
- Network > Unconfigure
- Network > VLAN
- Network > WANOptimization
- 附录 P. Main > Network > Security (IPsec) 命令
- 附录 Q. Main > Reports 命令
- 附录 R. Main > Settings 命令
- Settings > Cloud
- Settings > Deduplication
- Settings > FibreTransport
- Settings > iSCSI > Initiator
- Settings > iSCSI > Interface
- Settings > iSCSI > Target
- Settings > LogForwarding
- Settings > LifeCycle
- Settings > LiveUpdateServer
- Settings > NetBackup
- Settings > Password
- Settings > Share
- Settings > SNMP polling
- Settings > Sysctl
- Settings > SystemLocale
- 附录 S. Main > Settings > Alerts 命令
- 附录 T. Main > Settings > Notifications 视图命令
- 附录 U. Main > Settings > Security 命令
- 附录 V. Main > Support 命令
- Support > Checkpoint
- Support > Cleanup > RemoveShelfEntries
- Support > Cleanup > ResetDIMMErrors
- Support > Collect
- Support > DataCollect
- Support > Disk
- Support > Errors
- Support > FactoryReset
- Support > FibreTransport
- Support > InfraServices
- Support > iostat
- Support > IPMI
- Support > KillRemoteCall
- Support > Logs
- Support > Maintenance
- Support > Messages
- Support > NBDNA
- Support > nbperfchk
- Support > NBSU
- Support > Processes
- Support > RAID
- Support > Reboot
- Support > RecoverStorage
- Support > Service
- Support > ServiceAllowed
- Support > Show
- Support > Shutdown
- Support > Storage ClearReservations
- Support > Storage Reset
- Support > Storage SanityCheck
- Support > Test
关于 Appliance 视图下的命令
从 Appliance 视图中，可以执行以下功能：
设置设备的管理角色。
配置设备角色。
检查设备的状态。
淘汰现有介质设备。
查看设备的标识。
查看 NetBackup 重复数据删除密码。
下表汇总了 Appliance 视图中在初始配置期间可用的命令，具体取决于所选的设备角色。
表：
|
命令 |
说明 |
|---|---|
|
Management |
使用此命令可以设置 NetBackup Appliance 的管理角色。 |
|
Master |
使用此命令可将设备配置为 NetBackup 主设备。 |
|
Media |
使用此命令可将设备配置为 NetBackup 介质服务器。 |
|
Remove |
使用此命令可淘汰现有介质设备。 请参见 Appliance > Remove 。 |
|
ShowDedupPassword |
用于显示域的 NetBackup 重复数据删除密码。 |
|
ShowIdentity |
使用此命令可显示当前设备标识，以满足不同颁发机构的要求。 |
|
Status |
使用此命令可显示当前设备状态信息。 请参见Appliance > Status 。 |
注意:
Master 和 Media 命令仅在设备初始配置期间可用。