请输入搜索词进行查询
搜索 <book_title>...
Veritas NetBackup™ Appliance 命令参考指南
Last Published:
2017-12-04
Product(s):
Appliances (3.1 (5340), 3.1 (5330), 3.1 (5240), 3.1 (5230), 3.1 (5220))
- 概述
- 附录 A. Main > Appliance 命令
- 附录 B. Main > Manage > FibreChannel 命令
- 附录 C. Main > Manage > HighAvailability 命令
- 附录 D. Main > Manage > Libraries 命令
- 附录 E. Main > Manage > Libraries > Advanced > ACS 命令
- Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
- Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
- Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
- Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
- Manage > Libraries > Advanced > ACS > TestACS
- Manage > Libraries > Advanced > ACS > ViewVMconf
- 附录 F. Main > Manage > License 命令
- 附录 G. Main > Manage > MountPoints 命令
- 附录 H. Main > Manage > NetBackup CLI 命令
- 附录 I. Main > Manage > OpenStorage 命令
- 附录 J. Main > Manage > Software 命令
- Manage > Software > Cancel
- Manage > Software > Delete
- Manage > Software > Download
- Manage > Software > DownloadProgress
- Manage > Software > Firmware
- Manage > Software > Install
- Manage > Software > List
- Manage > Software > LiveUpdateClients
- Manage > Software > Readme
- Manage > Software > Rollback
- Manage > Software > Share
- Manage > Software > UpgradeStatus
- 附录 K. Main > Manage > Storage 命令
- 附录 L. Main > Manage > Tapes 命令
- 附录 M. Main > Manage > Certificates 命令
- 附录 N. Main > Monitor 命令
- 附录 O. Main > Network 命令
- Network > Configure
- Network > Date
- Network > DNS
- Network > Gateway
- Network > Hostname
- Network > Hosts
- Network > IPv4
- Network > IPv6
- Network > LinkAggregation
- Network > NetStat
- Network > NTPServer
- Network > Ping
- Network > SetProperty
- Network > Show
- Network > TimeZone
- Network > TraceRoute
- Network > Unconfigure
- Network > VLAN
- Network > WANOptimization
- 附录 P. Main > Network > Security (IPsec) 命令
- 附录 Q. Main > Reports 命令
- 附录 R. Main > Settings 命令
- Settings > Cloud
- Settings > Deduplication
- Settings > FibreTransport
- Settings > iSCSI > Initiator
- Settings > iSCSI > Interface
- Settings > iSCSI > Target
- Settings > LogForwarding
- Settings > LifeCycle
- Settings > LiveUpdateServer
- Settings > NetBackup
- Settings > Password
- Settings > Share
- Settings > SNMP polling
- Settings > Sysctl
- Settings > SystemLocale
- 附录 S. Main > Settings > Alerts 命令
- 附录 T. Main > Settings > Notifications 视图命令
- 附录 U. Main > Settings > Security 命令
- 附录 V. Main > Support 命令
- Support > Checkpoint
- Support > Cleanup > RemoveShelfEntries
- Support > Cleanup > ResetDIMMErrors
- Support > Collect
- Support > DataCollect
- Support > Disk
- Support > Errors
- Support > FactoryReset
- Support > FibreTransport
- Support > InfraServices
- Support > iostat
- Support > IPMI
- Support > KillRemoteCall
- Support > Logs
- Support > Maintenance
- Support > Messages
- Support > NBDNA
- Support > nbperfchk
- Support > NBSU
- Support > Processes
- Support > RAID
- Support > Reboot
- Support > RecoverStorage
- Support > Service
- Support > ServiceAllowed
- Support > Show
- Support > Shutdown
- Support > Storage ClearReservations
- Support > Storage Reset
- Support > Storage SanityCheck
- Support > Test
名称
Main > Support > FibreTransport — 用于管理光纤传输 (FT) 高级设置。
大纲
FibreTransport ChunkSize Show
FibreTransport ChunkSize Set ChunkSize
描述
可以使用 FibreTransport 命令执行以下操作：
显示通过 FT 到其他 NetBackup 设备的优化复制和复制的片段大小。
设置通过 FT 到其他 NetBackup 设备的优化复制和复制的片段大小
选项
- FibreTranport ChunkSize Show
使用此命令可显示通过 FT 到其他 NetBackup 设备的优化复制和复制的当前片段大小。
- FibreTranport ChunkSize Set ChunkSize
使用此命令设置块大小 (KB)。
片段大小的默认值为 0，这意味着未指定也未使用片段大小。如果将片段大小设置为等于或大于 1 的值，则表示您指定了发送到 FC 网络的每个数据片段的大小。可用的片段大小值为 1-2048，以 KB 为单位。推荐的值为 128 KB、256 KB、512 KB、1024 KB 和 2048 KB。您也可能需要设置其他值。
注意:
对于通过 FT 的优化复制和复制，不需要片段大小设置。它很大程度上取决于用户部署和网络状态。如果您认为需要使用片段大小，则可以根据需要调整片段大小来确定适合您的环境和当前网络状态的适当值。
有关如何使用 FT 片段大小的更多信息，请参见《NetBackup Appliance 光纤通道指南》。
示例
以下是运行 FibreTransport ChunkSize Show 命令时的信息示例。
appliance.support> FibreTransport ChunkSize Set 2 [Info] Current deduplication chunk size is 0 KB.
以下是运行 FibreTransport ChunkSize Set Value 命令时的信息示例。
appliance.support> FibreTransport ChunkSize Set 2 [Info] New deduplication chunk size is 2 KB.