Veritas NetBackup™ Appliance 命令参考指南
- 概述
- 附录 A. Main > Appliance 命令
- 附录 B. Main > Manage > FibreChannel 命令
- 附录 C. Main > Manage > HighAvailability 命令
- 附录 D. Main > Manage > Libraries 命令
- 附录 E. Main > Manage > Libraries > Advanced > ACS 命令
- Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
- Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
- Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
- Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
- Manage > Libraries > Advanced > ACS > TestACS
- Manage > Libraries > Advanced > ACS > ViewVMconf
- 附录 F. Main > Manage > License 命令
- 附录 G. Main > Manage > MountPoints 命令
- 附录 H. Main > Manage > NetBackup CLI 命令
- 附录 I. Main > Manage > OpenStorage 命令
- 附录 J. Main > Manage > Software 命令
- Manage > Software > Cancel
- Manage > Software > Delete
- Manage > Software > Download
- Manage > Software > DownloadProgress
- Manage > Software > Firmware
- Manage > Software > Install
- Manage > Software > List
- Manage > Software > LiveUpdateClients
- Manage > Software > Readme
- Manage > Software > Rollback
- Manage > Software > Share
- Manage > Software > UpgradeStatus
- 附录 K. Main > Manage > Storage 命令
- 附录 L. Main > Manage > Tapes 命令
- 附录 M. Main > Manage > Certificates 命令
- 附录 N. Main > Monitor 命令
- 附录 O. Main > Network 命令
- Network > Configure
- Network > Date
- Network > DNS
- Network > Gateway
- Network > Hostname
- Network > Hosts
- Network > IPv4
- Network > IPv6
- Network > LinkAggregation
- Network > NetStat
- Network > NTPServer
- Network > Ping
- Network > SetProperty
- Network > Show
- Network > TimeZone
- Network > TraceRoute
- Network > Unconfigure
- Network > VLAN
- Network > WANOptimization
- 附录 P. Main > Network > Security (IPsec) 命令
- 附录 Q. Main > Reports 命令
- 附录 R. Main > Settings 命令
- Settings > Cloud
- Settings > Deduplication
- Settings > FibreTransport
- Settings > iSCSI > Initiator
- Settings > iSCSI > Interface
- Settings > iSCSI > Target
- Settings > LogForwarding
- Settings > LifeCycle
- Settings > LiveUpdateServer
- Settings > NetBackup
- Settings > Password
- Settings > Share
- Settings > SNMP polling
- Settings > Sysctl
- Settings > SystemLocale
- 附录 S. Main > Settings > Alerts 命令
- 附录 T. Main > Settings > Notifications 视图命令
- 附录 U. Main > Settings > Security 命令
- 附录 V. Main > Support 命令
- Support > Checkpoint
- Support > Cleanup > RemoveShelfEntries
- Support > Cleanup > ResetDIMMErrors
- Support > Collect
- Support > DataCollect
- Support > Disk
- Support > Errors
- Support > FactoryReset
- Support > FibreTransport
- Support > InfraServices
- Support > iostat
- Support > IPMI
- Support > KillRemoteCall
- Support > Logs
- Support > Maintenance
- Support > Messages
- Support > NBDNA
- Support > nbperfchk
- Support > NBSU
- Support > Processes
- Support > RAID
- Support > Reboot
- Support > RecoverStorage
- Support > Service
- Support > ServiceAllowed
- Support > Show
- Support > Shutdown
- Support > Storage ClearReservations
- Support > Storage Reset
- Support > Storage SanityCheck
- Support > Test
名称
Main > Manage > Storage > Show — 查看 NetBackup 存储信息。
大纲
Show ALL
Show Disk
Show Distribution
Show Partition [Info][PartitionType][Name]
描述
通过此命令查看您的设备中的存储设备和分区的存储容量和参数。
注意:
页面上或者使用 NetBackup Appliance 上的 命令所显示的介质服务器重复数据删除池 (MSDP) 分区的“可用”值和“所用大小”值，可能不是 MSDP 分区的完整可用空间或已用空间。这是因为文件系统和 MSDP 已保留部分空间。文件系统保留空间供自己使用。此外，MSDP 还为重复数据删除数据库和事务日志保留了 4% 的存储空间。
检查 NetBackup 管理控制台的 MSDP 磁盘池大小以获取 MSDP 统计数据。
选项
- Show All
此命令可显示所有存储信息。
- Show Disk
此命令可显示存储磁盘 ID、类型、容量、未分配空间和状态。
- Show Distribution
此命令可显示磁盘上每个分区的存储分布。
- Show Partition [Info][PartitionType][Name]
显示存储分布信息。可以指定以下三个选项：
参数 1 - [Info]
指定要查看使用情况信息或磁盘池和存储单元配置还是同时查看两者。可用选项为
ALL、Configuration和Usage。默认值为ALL。参数 2 - [PartitionType]
指定分区类型。可用选项为
ALL、AdvancedDisk、Configuration、MSDP、MSDPCatalog和Share。默认值为ALL。参数 3 - [Name]
指定分区的数字名称。例如，“0”。可以在 Show All 输出中找到分区名称。默认值为
ALL，将显示指定类型的所有分区的信息。例如，要查看所有 MSDP 分区的存储单元和磁盘池配置，请运行以下命令：
Show Partition Configuration MSDP ALL
要查看所有分区的使用情况信息，请运行以下命令：
Show Partition Usage ALL ALL
示例
以下是 Show Partition Configuration MSDP ALL 命令的示例输出：
MSDP ------------------------------------- Disk Pool (DP) | Storage Unit (STU) ------------------------------------- dp_disk_abc123 | stu_disk_abc123