Important Update: Cohesity Products Documentation

All Cohesity product documentation are now managed via the Cohesity Docs Portal: https://docs.cohesity.com/HomePage/Content/home.htm. Some documentation available here may not reflect the latest information or may no longer be accessible.

Veritas™ 5260 Appliance Hardware Installation Guide

Last Published:
Product(s): Appliances (Version Not Specified)
Platform: Veritas 5260
  1. Hardware overview
    1.  
      About the appliance and the storage shelves
    2.  
      Appliance drives
    3. About the 5260 Appliance control panel
      1.  
        About the System Status LED states
      2.  
        About the Power button LED states
      3.  
        About the integrated BMC beep codes
    4.  
      Appliance rear panel
    5.  
      Storage shelf disk drives
    6.  
      Storage shelf control panel
    7.  
      Storage shelf rear panel
    8.  
      Cables
    9.  
      About IPMI configuration
    10.  
      Product documentation
  2. Preinstallation requirements
    1.  
      Customer-provided environment and supplies
    2.  
      Appliance shipping container contents
    3.  
      Storage shelf shipping container contents
    4.  
      Best practices for rack installation
    5.  
      Determining rack locations
    6.  
      Storage shelf rack requirements
    7.  
      Heat dissipation
    8.  
      Verifying SAS-3 cable length
    9.  
      Prerequisites for IPMI configuration
  3. Installation procedures
    1.  
      Installing the storage shelf rack rails
    2.  
      Installing the storage shelf into a rack
    3.  
      Installing the appliance rack rails
    4.  
      Installing the appliance into a rack
    5.  
      Understanding appliance and storage shelf connections
    6.  
      Connecting an appliance to one storage shelf
    7.  
      Connecting an appliance to more than one storage shelf
  4. Next steps after installation
    1.  
      Connecting the network cables
    2.  
      Connecting the power cords
    3.  
      Turning on the hardware and verifying operation
    4.  
      Configuring the Veritas Remote Management Interface from a Flex Appliance
    5.  
      Configuring the Veritas Remote Management Interface using laptop
    6.  
      Accessing and using the Veritas Remote Management interface
  5. Appendix A. Adding one or more storage shelves to an operating appliance that does not have any storage shelves
    1.  
      Overview
    2.  
      Preparing the appliance
    3.  
      Removing the appliance cover
    4.  
      Installing the Expansion Storage Kit components
    5.  
      Replacing the appliance cover
    6. Connecting the storage shelves to the appliance
      1.  
        Connecting one storage shelf to an appliance
      2.  
        Connecting two storage shelves to an appliance
      3.  
        Connecting three storage shelves to an appliance
      4.  
        Connecting four storage shelves to an appliance
      5.  
        Connecting the fifth storage shelf to an appliance
      6.  
        Connecting the sixth storage shelf to an appliance
  6. Appendix B. Adding storage shelves to an operating appliance that has at least one storage shelf attached
    1.  
      Overview
    2.  
      Additional storage shelf scenarios
    3. Recabling to connect additional storage shelves
      1.  
        Connecting additional shelves to an appliance that already has one operating shelf
      2.  
        Connecting additional shelves to an appliance that already has two operating shelf
      3.  
        Connecting additional shelves to an appliance that already has three operating shelf
  7. Appendix C. Configuring the disk space for new Flex Expansion Storage Shelves
    1.  
      Adding the disk space of an Expansion Storage Shelf from the Flex Appliance Console
  8.  
    Index

Prerequisites for IPMI configuration

Verify the following configuration prerequisites:

  • The remote management port auto-negotiates its link speed to 1 Gbps.

    Note:

    If the IPMI port is connected to a managed switch port, it is recommended that you configure the switch port to auto-negotiation

  • If a firewall exists between the appliance and the remote devices that manage an appliance (like a laptop computer), open the following ports:

    66

    SOL SSH

    80

    HTTP

    162

    SNMP

    443

    HTTPS

    623

    Floppy/USB media

    627

    Secured Floppy/USB media

    5120

    CD

    5124

    Secured CD

    5900

    KVM

    5902

    Secured KVM

    Note:

    If you have a private internal network, remember to configure the settings accordingly in your network address translation (NAT).

  • The remote management port must be configured as a DHCP or static address.