Veritas 5340 Appliance Product Description

Last Published:
Product(s): Appliances (Version Not Specified)
Platform: Veritas 5340
  1. About the Veritas 5340 Appliance
    1.  
      About the Veritas 5340 Appliance
    2.  
      Features and components of the appliance
    3.  
      Locating the appliance serial number
    4. Compute node disk drive configurations
      1.  
        About the compute node disk drive LEDs
    5.  
      About the compute node front panel USB port
    6. About the compute node control panel
      1.  
        About the System Status LED states
      2.  
        About the Power button LED states
    7. About the compute node rear panel
      1.  
        Available NetBackup 5340 Appliance PCIe-based I/O configurations
      2. Total 5340 Appliance on-board and PCIe-based I/O ports
        1.  
          QLE2692 dual-port 16Gb Fibre Channel host bus adapter
        2.  
          QLE8442 dual-port 10Gb Ethernet/iSCSI capable card with SFP+ modules
        3.  
          QLE2562 dual-port 8Gb Fibre Channel host bus adapter with SFP+ modules
      3.  
        Appliance network interface card port assignments
  2. About the Veritas 5U84 Storage Shelves
    1. About Veritas 5340 Appliance storage shelves
      1.  
        Available appliance storage options
      2. About the Veritas 5U84 Storage Shelf disk drive drawers
        1.  
          Disk drive slot numbering
        2.  
          Disk Drive In Carrier (DDIC) modules
        3.  
          Disk Drive Drawer printed circuit board (PCB) assemblies
        4.  
          Drawer Sideplane Status panels
        5.  
          Drawer Sideplane hot swap LED indicators
      3.  
        5U84 Primary Storage Shelf and the 5U84 Expansion Storage Shelf control panel
    2. About the 5U84 Primary Storage Shelf and 5U84 Expansion Storage Shelf rear components
      1.  
        Veritas 5U84 Primary Storage Shelf RAID controllers
      2. Veritas 5U84 Expansion Storage Shelf Expansion I/O modules
        1.  
          Expansion I/O module Status LED location and conditions
        2.  
          Expansion I/O module SAS Activity LED location and conditions
      3.  
        Veritas 5U84 Storage Shelf cooling modules
      4.  
        5U84 Storage Shelf Power Supply Units
  3. Veritas 5340 Appliance and 5U84 Storage Shelf cables
    1.  
      Power cables
    2.  
      Network cable
    3.  
      Multi-mode fiber optic cable
    4.  
      SAS-3 cable
    5.  
      Twinaxial copper cables
  4. Appendix A. Technical specifications, Environmental/Protocol standards, and Compliance standards
    1.  
      5340 Appliance compute node technical specifications
    2.  
      Veritas 5U84 Storage Shelf technical specifications
    3.  
      Environmental specifications
    4.  
      Protocol standards
    5. Regulatory, compliance, and certification information
      1.  
        Product regulatory compliance
      2.  
        Product safety compliance
      3.  
        Product EMC Compliance - Class A Compliance
      4.  
        Product ecology compliance
      5.  
        Certifications / Registrations / Declarations
      6. Electromagnetic compatibility notices
        1.  
          FCC Verification Statement (USA)
        2.  
          ICES-003 (Canada)
        3.  
          CE Declaration of Conformity (Europe)
        4.  
          VCCI (Japan)
        5.  
          BSMI (Taiwan)
  5.  
    Index

FCC Verification Statement (USA)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to a radio or a television reception (can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.

  • Increase the separation between the equipment and the receiver.

  • Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

  • Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the grantee of this device can void the user's authority to operate the equipment. The customer is responsible to ensure compliance of the modified product. Only peripherals (computer input or output devices, terminals, printers, etc.) that comply with FCC Class A or B limits may be attached to this product. Operation with noncompliant peripherals is likely to result in interference to radio and TV reception. All cables that are used to connect to peripherals must be shielded and grounded. Operation with regulatory and compliance information 65 Electromagnetic compatibility notices the cables that are connected to peripherals that are not shielded and grounded may result in interference to radio and TV reception.