Veritas NetBackup™ Appliance Commands Reference Guide
- Overview
- 付録 A. Main > Appliance commands
- 付録 B. Main > Manage > FibreChannel commands
- 付録 C. Main > Manage > HighAvailability commands
- 付録 D. Main > Manage > Libraries commands
- 付録 E. Main > Manage > Libraries > Advanced > ACS commands
- Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
- Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
- Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
- Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
- Manage > Libraries > Advanced > ACS > TestACS
- Manage > Libraries > Advanced > ACS > ViewVMconf
- 付録 F. Main > Manage > License commands
- 付録 G. Main > Manage > MountPoints commands
- 付録 H. Main > Manage > NetBackup CLI commands
- 付録 I. Main > Manage > OpenStorage commands
- 付録 J. Main > Manage > Software commands
- Manage > Software > Cancel
- Manage > Software > Delete
- Manage > Software > Download
- Manage > Software > DownloadProgress
- Manage > Software > Firmware
- Manage > Software > Install
- Manage > Software > List
- Manage > Software > LiveUpdateClients
- Manage > Software > Readme
- Manage > Software > Rollback
- Manage > Software > Share
- Manage > Software > UpgradeStatus
- 付録 K. Main > Manage > Storage commands
- 付録 L. Main > Manage > Tapes commands
- 付録 M. Main > Manage > Certificates commands
- 付録 N. Main > Monitor commands
- 付録 O. Main > Network commands
- Network > Configure
- Network > Date
- Network > DNS
- Network > Gateway
- Network > Hostname
- Network > Hosts
- Network > IPv4
- Network > IPv6
- Network > LinkAggregation
- Network > NetStat
- Network > NTPServer
- Network > Ping
- Network > SetProperty
- Network > Show
- Network > TimeZone
- Network > TraceRoute
- Network > Unconfigure
- Network > VLAN
- Network > WANOptimization
- 付録 P. Main > Network > Security (IPsec) commands
- 付録 Q. Main > Reports commands
- 付録 R. Main > Settings commands
- Settings > Cloud
- Settings > Deduplication
- Settings > FibreTransport
- Settings > iSCSI > Initiator
- Settings > iSCSI > Interface
- Settings > iSCSI > Target
- Settings > LogForwarding
- Settings > LifeCycle
- Settings > LiveUpdateServer
- Settings > NetBackup
- ［設定 (Settings)］>［パスワード (Password)］
- Settings > Share
- Settings > SNMP polling
- Settings > Sysctl
- Settings > SystemLocale
- 付録 S. Main > Settings > Alerts commands
- 付録 T. Main > Settings > Notifications view commands
- 付録 U. Main > Settings > Security commands
- 付録 V. Main > Support commands
- Support > Checkpoint
- Support > Cleanup > RemoveShelfEntries
- Support > Cleanup > ResetDIMMErrors
- Support > Collect
- Support > DataCollect
- Support > Disk
- Support > Errors
- Support > FactoryReset
- Support > FibreTransport
- Support > InfraServices
- Support > iostat
- Support > IPMI
- Support > KillRemoteCall
- Support > Logs
- Support > Maintenance
- Support > Messages
- Support > NBDNA
- Support > nbperfchk
- Support > NBSU
- Support > Processes
- Support > RAID
- Support > Reboot
- Support > RecoverStorage
- Support > Service
- Support > ServiceAllowed
- Support > Show
- Support > Shutdown
- Support > Storage ClearReservations
- Support > Storage Reset
- Support > Storage SanityCheck
- Support > Test
名前
Main > Network > IPv4 — Change the IPv4 address of a network interface.
概要
IPv4 IPAddress NetMask [InterfaceNames]
DESCRIPTION
Use this command to change the IPv4 address of a network interface. You can use this command to configure multiple network interfaces. To do that, you must repeat the command for each network that you want to add.
注意:
If you have an operational NetBackup 53xx high availability configuration, do not change the IPv4 address on the public network interface card (NIC).
OPTIONS
- IPv4 IPAddress NetMask [InterfaceNames]
Change the IPv4 address of a network interface.
Where IPAddress is the name of the new IPv4 address. The NetMask variable is the name of the netmask. The [InterfaceNames] parameter is a comma-separated list of interface names. The [InterfaceNames] field is optional. If an interface name is not provided, the command searches for an interface and configures it.
You may enter a VLAN interface ID for the [InterfaceNames] parameter. However, unlike the physical interface or bond interface, if you do not provide a value for the for the [InterfaceNames] parameter, the command does not search for VLAN interfaces.