Veritas NetBackup™ Appliance Commands Reference Guide
- Overview
- 付録 A. Main > Appliance commands
- 付録 B. Main > Manage > FibreChannel commands
- 付録 C. Main > Manage > HighAvailability commands
- 付録 D. Main > Manage > Libraries commands
- 付録 E. Main > Manage > Libraries > Advanced > ACS commands
- Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
- Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
- Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
- Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
- Manage > Libraries > Advanced > ACS > TestACS
- Manage > Libraries > Advanced > ACS > ViewVMconf
- 付録 F. Main > Manage > License commands
- 付録 G. Main > Manage > MountPoints commands
- 付録 H. Main > Manage > NetBackup CLI commands
- 付録 I. Main > Manage > OpenStorage commands
- 付録 J. Main > Manage > Software commands
- Manage > Software > Cancel
- Manage > Software > Delete
- Manage > Software > Download
- Manage > Software > DownloadProgress
- Manage > Software > Firmware
- Manage > Software > Install
- Manage > Software > List
- Manage > Software > LiveUpdateClients
- Manage > Software > Readme
- Manage > Software > Rollback
- Manage > Software > Share
- Manage > Software > UpgradeStatus
- 付録 K. Main > Manage > Storage commands
- 付録 L. Main > Manage > Tapes commands
- 付録 M. Main > Manage > Certificates commands
- 付録 N. Main > Monitor commands
- 付録 O. Main > Network commands
- Network > Configure
- Network > Date
- Network > DNS
- Network > Gateway
- Network > Hostname
- Network > Hosts
- Network > IPv4
- Network > IPv6
- Network > LinkAggregation
- Network > NetStat
- Network > NTPServer
- Network > Ping
- Network > SetProperty
- Network > Show
- Network > TimeZone
- Network > TraceRoute
- Network > Unconfigure
- Network > VLAN
- Network > WANOptimization
- 付録 P. Main > Network > Security (IPsec) commands
- 付録 Q. Main > Reports commands
- 付録 R. Main > Settings commands
- Settings > Cloud
- Settings > Deduplication
- Settings > FibreTransport
- Settings > iSCSI > Initiator
- Settings > iSCSI > Interface
- Settings > iSCSI > Target
- Settings > LogForwarding
- Settings > LifeCycle
- Settings > LiveUpdateServer
- Settings > NetBackup
- ［設定 (Settings)］>［パスワード (Password)］
- Settings > Share
- Settings > SNMP polling
- Settings > Sysctl
- Settings > SystemLocale
- 付録 S. Main > Settings > Alerts commands
- 付録 T. Main > Settings > Notifications view commands
- 付録 U. Main > Settings > Security commands
- 付録 V. Main > Support commands
- Support > Checkpoint
- Support > Cleanup > RemoveShelfEntries
- Support > Cleanup > ResetDIMMErrors
- Support > Collect
- Support > DataCollect
- Support > Disk
- Support > Errors
- Support > FactoryReset
- Support > FibreTransport
- Support > InfraServices
- Support > iostat
- Support > IPMI
- Support > KillRemoteCall
- Support > Logs
- Support > Maintenance
- Support > Messages
- Support > NBDNA
- Support > nbperfchk
- Support > NBSU
- Support > Processes
- Support > RAID
- Support > Reboot
- Support > RecoverStorage
- Support > Service
- Support > ServiceAllowed
- Support > Show
- Support > Shutdown
- Support > Storage ClearReservations
- Support > Storage Reset
- Support > Storage SanityCheck
- Support > Test
名前
Manage > HighAvailability > RemoveNode — Remove a node from a high availability (HA) configuration.
概要
RemoveNode HostName
DESCRIPTION
This command removes a configured compute node from an HA configuration for maintenance, replacement, or repurposing. When you remove a node, the data that was backed up with that node remains available from the other node in the HA configuration.
メモ:
You cannot perform this operation with the virtual hostname or virtual IP address. You need to use the physical hostname or physical IP address.
You can only revert the partner node to be the non-HA node by running the RemoveNode command. Other operations, such as factory reset, or rolling back to a non-ha checkpoint, may cause the malfunction of the HA configuration.
OPTIONS
- RemoveNode HostName
Use this command to remove a node from an HA configuration. The HostName is the hostname of the node. This command can only be run on the node that is not to be removed in the configuration.
If you need to add the node back to the HA configuration, perform the following tasks orderly:
Refer to the FactoryReset command to reset the node to the factory default setting.
メモ:
Before you perform the factory reset, make sure that you performed the following procedure:
Make sure that the node is removed from any HA configuration.
Make sure to remove the Ethernet cables between the two nodes and the FC cables between the node and the Primary Storage Shelf.
Refer to the AddNode command.
If you need to replace it with a different node, refer to the NetBackup Appliance High Availability Reference Guide.