Veritas NetBackup™ Appliance Commands Reference Guide

Last Published:
Product(s): Appliances (3.1 (5340), 3.1 (5330), 3.1 (5240), 3.1 (5230), 3.1 (5220))
  1. Overview
    1.  
      NetBackup Appliance Shell Menuについて
    2. NetBackup Appliance Shell Menuへのログオン
      1.  
        構成されていないアプライアンスに対するコマンドの制限
    3.  
      NetBackup Appliance Shell Menuの使用
    4. NetBackup Appliance Shell Menuコマンドビューについて
      1.  
        ［アプライアンス (Appliance)］ビューのコマンドについて
      2.  
        ［管理 (Manage)］ビューのコマンドについて
      3.  
        About the commands under the Monitor view
      4.  
        ［ネットワーク (Network)］ビューのコマンドについて
      5.  
        ［レポート (Reports)］ビューのコマンドについて
      6.  
        ［設定 (Settings)］ビューのコマンドについて
      7.  
        ［サポート (Support)］ビューのコマンドについて
  2. 付録 A. Main > Appliance commands
    1.  
      Appliance > Master
    2.  
      Appliance > Media
    3.  
      Appliance > Management
    4.  
      Appliance > Remove
    5.  
      Appliance > ShowDedupPassword
    6.  
      Appliance > ShowIdentity
    7.  
      Appliance > Status
  3. 付録 B. Main > Manage > FibreChannel commands
    1.  
      Manage > FibreChannel > Clean
    2.  
      Manage > FibreChannel > Configure
    3.  
      Manage > FibreChannel > Reset
    4.  
      Manage > FibreChannel > Scan
    5.  
      Manage > FibreChannel > Show
    6.  
      Manage > FibreChannel > Statistics
  4. 付録 C. Main > Manage > HighAvailability commands
    1.  
      Manage > HighAvailability > AddNode
    2.  
      Manage > HighAvailability > GetAssetTag
    3.  
      Manage > HighAvailability > RemoveNode
    4.  
      Manage > HighAvailability > Setup
    5.  
      Manage > HighAvailability > Status
    6.  
      Manage > HighAvailability > Switchover
  5. 付録 D. Main > Manage > Libraries commands
    1.  
      Manage > Libraries > Configure
    2.  
      Manage > Libraries > Deny
    3.  
      Manage > Libraries > Down
    4.  
      Manage > Libraries > Inventory
    5.  
      Manage > Libraries > List
    6.  
      Manage > Libraries > Requests
    7.  
      Manage > Libraries > Reset
    8.  
      Manage > Libraries > Resubmit
    9.  
      Manage > Libraries > Up
  6. 付録 E. Main > Manage > Libraries > Advanced > ACS commands
    1.  
      Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
    2.  
      Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
    3.  
      Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
    4.  
      Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
    5.  
      Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
    6.  
      Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
    7.  
      Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
    8.  
      Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
    9.  
      Manage > Libraries > Advanced > ACS > TestACS
    10.  
      Manage > Libraries > Advanced > ACS > ViewVMconf
  7. 付録 F. Main > Manage > License commands
    1.  
      Manage > License > Add
    2.  
      Manage > License > List
    3.  
      Manage > License > ListInfo
    4.  
      Manage > License > Remove
  8. 付録 G. Main > Manage > MountPoints commands
    1.  
      Manage > MountPoints > List
    2.  
      Manage > MountPoints > Mount
    3.  
      Manage > MountPoints > Unmount
  9. 付録 H. Main > Manage > NetBackup CLI commands
    1.  
      Manage > NetBackupCLI > Create
    2.  
      Manage > NetBackupCLI > Delete
    3.  
      Manage > NetBackupCLI > List
    4.  
      Manage > NetBackupCLI > PasswordExpiry
  10. 付録 I. Main > Manage > OpenStorage commands
    1.  
      Manage > OpenStorage > Install
    2.  
      Manage > OpenStorage > List
    3.  
      Manage > OpenStorage > Readme
    4.  
      Manage > OpenStorage > Share
    5.  
      Manage > OpenStorage > Uninstall
  11. 付録 J. Main > Manage > Software commands
    1.  
      Manage > Software > Cancel
    2.  
      Manage > Software > Delete
    3.  
      Manage > Software > Download
    4.  
      Manage > Software > DownloadProgress
    5.  
      Manage > Software > Firmware
    6.  
      Manage > Software > Install
    7.  
      Manage > Software > List
    8.  
      Manage > Software > LiveUpdateClients
    9.  
      Manage > Software > Readme
    10.  
      Manage > Software > Rollback
    11.  
      Manage > Software > Share
    12.  
      Manage > Software > UpgradeStatus
  12. 付録 K. Main > Manage > Storage commands
    1.  
      Manage > Storage > Add
    2.  
      Manage > Storage > Create
    3.  
      Manage > Storage > Delete
    4.  
      Manage > Storage > Edit
    5.  
      Manage > Storage > Monitor
    6.  
      Manage > Storage > Move
    7.  
      Manage > Storage > Remove
    8.  
      Manage > Storage > Resize
    9.  
      Manage > Storage > Scan
    10.  
      Manage > Storage > Show
    11.  
      Manage > Storage > Erase
  13. 付録 L. Main > Manage > Tapes commands
    1.  
      Manage > Tapes > Cleaning
    2.  
      Manage > Tapes > Delete
    3.  
      Manage > Tapes > Eject
    4.  
      Manage > Tapes > Freeze
    5.  
      Manage > Tapes > Inventory
    6.  
      Manage > Tapes > List
    7.  
      Manage > Tapes > ListNetBackupMedia
    8.  
      Manage > Tapes > Suspend
    9.  
      Manage > Tapes > Unfreeze
    10.  
      Manage > Tapes > Unsuspend
  14. 付録 M. Main > Manage > Certificates commands
    1.  
      Manage > Certificates > Generate
    2.  
      Manage > Certificates > Delete
  15. 付録 N. Main > Monitor commands
    1.  
      Monitor > Beacon
    2.  
      Monitor > MemoryStatus
    3.  
      Monitor > NetBackup
    4.  
      Monitor > NetworkStatus
    5.  
      ［監視 (Monitor)］>［SDCS］
    6.  
      Monitor > Top
    7.  
      Monitor > Uptime
    8.  
      Monitor > Who
    9.  
      Monitor > Hardware
  16. 付録 O. Main > Network commands
    1.  
      Network > Configure
    2.  
      Network > Date
    3.  
      Network > DNS
    4.  
      Network > Gateway
    5.  
      Network > Hostname
    6.  
      Network > Hosts
    7.  
      Network > IPv4
    8.  
      Network > IPv6
    9.  
      Network > LinkAggregation
    10.  
      Network > NetStat
    11.  
      Network > NTPServer
    12.  
      Network > Ping
    13.  
      Network > SetProperty
    14.  
      Network > Show
    15.  
      Network > TimeZone
    16.  
      Network > TraceRoute
    17.  
      Network > Unconfigure
    18.  
      Network > VLAN
    19.  
      Network > WANOptimization
  17. 付録 P. Main > Network > Security (IPsec) commands
    1.  
      Network > IPsec > Configure
    2.  
      Network > IPsec > Delete
    3.  
      Network > IPsec > Export
    4.  
      Network > IPsec > Import
    5.  
      Network > IPsec > Provision
    6.  
      Network > IPsec > Refresh
    7.  
      Network > IPsec > Show
    8.  
      Network > IPsec > Unconfigure
  18. 付録 Q. Main > Reports commands
    1.  
      Reports > Deduplication
    2.  
      Reports > Process
  19. 付録 R. Main > Settings commands
    1.  
      Settings > Cloud
    2.  
      Settings > Deduplication
    3.  
      Settings > FibreTransport
    4.  
      Settings > iSCSI > Initiator
    5.  
      Settings > iSCSI > Interface
    6.  
      Settings > iSCSI > Target
    7.  
      Settings > LogForwarding
    8.  
      Settings > LifeCycle
    9.  
      Settings > LiveUpdateServer
    10.  
      Settings > NetBackup
    11.  
      ［設定 (Settings)］>［パスワード (Password)］
    12.  
      Settings > Share
    13.  
      Settings > SNMP polling
    14.  
      Settings > Sysctl
    15.  
      Settings > SystemLocale
  20. 付録 S. Main > Settings > Alerts commands
    1.  
      Settings > Alerts > CallHome
    2.  
      Settings > Alerts > Email
    3.  
      Settings > Alerts > Hardware
    4.  
      Settings > Alerts > SNMP
  21. 付録 T. Main > Settings > Notifications view commands
    1.  
      Settings > Notifications > LoginBanner
  22. 付録 U. Main > Settings > Security commands
    1.  
      Settings > Security > Authorization
    2.  
      Settings > Security > Authentication > ActiveDirectory
    3.  
      Settings > Security > Authentication > Kerberos
    4.  
      Settings > Security > Authentication > LDAP
    5.  
      Settings > Security > Authentication > LocalUser
    6.  
      Settings > Security > STIG
  23. 付録 V. Main > Support commands
    1.  
      Support > Checkpoint
    2.  
      Support > Cleanup > RemoveShelfEntries
    3.  
      Support > Cleanup > ResetDIMMErrors
    4.  
      Support > Collect
    5.  
      Support > DataCollect
    6.  
      Support > Disk
    7.  
      Support > Errors
    8.  
      Support > FactoryReset
    9.  
      Support > FibreTransport
    10.  
      Support > InfraServices
    11.  
      Support > iostat
    12.  
      Support > IPMI
    13.  
      Support > KillRemoteCall
    14.  
      Support > Logs
    15.  
      Support > Maintenance
    16.  
      Support > Messages
    17.  
      Support > NBDNA
    18.  
      Support > nbperfchk
    19.  
      Support > NBSU
    20.  
      Support > Processes
    21.  
      Support > RAID
    22.  
      Support > Reboot
    23.  
      Support > RecoverStorage
    24.  
      Support > Service
    25.  
      Support > ServiceAllowed
    26.  
      Support > Show
    27.  
      Support > Shutdown
    28.  
      Support > Storage ClearReservations
    29.  
      Support > Storage Reset
    30.  
      Support > Storage SanityCheck
    31.  
      Support > Test

名前

Main > Support >NBDNA — NBDNA ユーティリティを使ってネットワークトレースの作成と削除を行います。

概要

NBDNA Create phase

NBDNA Remove

説明

このコマンドは、アプライアンスの NBDNA (NetBackup Domain Network Analyzer) ユーティリティとともに使います。NBDNA ユーティリティは以下の情報を分析します。

  • ネットワークの問題の NetBackup ドメインおよびその構成

  • NetBackup のパフォーマンス

  • ホスト名のルックアップに関する動作および NetBackup ドメイン内の NetBackup ホストとそのロール間の接続性

オプション

NBDNA Create phase

NBDNA ユーティリティを使ってネットワークトレースの作成と削除を行います。

ここで、phase はどのテストフェーズを実行するかを指定するために使います。phase 0、phase 1、phase 2 のいずれかです。

Phase 0: デフォルトモード。名前ルックアップテストとソケット接続テスト。

Phase 1: Phase 0 を含みます。サーバーリストの基本 NetBackup サービステストを追加します。

Phase 2: Phase 0 を含みます。サーバーリストとクライアントリストの基本 NetBackup サービステストを追加します。

NBDNA Remove

NBDNA ユーティリティが生成するすべての既存のトレースファイルを削除するために使います。